Cummins ISX ECM repair gets more heavy trucks back on the road than almost any other ECM job we do. The ISX powers a huge share of Class 8 tractors, and its engine computer works hard: bolted to a hot, vibrating engine, exposed to water and voltage spikes.
This guide lists 8 signs your ISX ECM needs repair, what to rule out first, which ISX ECMs we repair, Cummins ISX ECM repair cost and how the process works.
In this guide
8 signs you need Cummins ISX ECM repair
- Crank, no start: the engine cranks with good fuel supply but never fires.
- Stalling: the engine dies at idle or under load and may restart after cooling.
- Dead cylinder: one injector stops firing and stays dead with a known-good injector.
- Derate with no clear cause: low power without a sensor fault to explain it.
- No communication: the diagnostic tool cannot connect while other modules respond.
- Many unrelated codes: several sensors report faults at the same time.
- Heat-related faults: problems that appear only when the engine is hot.
- Problems after washing or rain: water in the ECM connectors.
Rule these out first
- Batteries and cables: load-test and check cranking voltage.
- Grounds: clean and tighten engine and frame grounds.
- ECM power: measure power and ground at the ECM connector.
- Connectors: look for water, corrosion or pushed-back pins.
- Injector harness: on a dead cylinder, check the harness and injector.
- Sensors: a shorted sensor can pull down the 5-volt supply.
Our truck ECM diagnosis guide walks through each test.
ISX ECMs we repair
| Module | Example part numbers |
|---|---|
| CM570 | 3681404, 3681405, 3680509 |
| CM870 / CM871 | 3682729, 3683289, 3684009, 3684275 |
The module name and part number are on the ECM label. Our Cummins ISX ECM guide explains how to tell the modules apart, and when repair or replacement makes sense.
Cummins ISX ECM repair cost
On our price list (November 2026), ISX ECM repair costs $399.99 for both CM570 and CM870 and CM871 units, with a 1-year warranty.
If our bench test finds nothing wrong, you pay only the $149 diagnostic fee. Return shipping includes $100 of insurance.
How the repair works
- Buy the repair listing for your module, or ship us the ECM with your contact details.
- We email you when it arrives and place it in line.
- We bench-test it, repair the failed parts and check every other circuit.
- We load-test it and ship it back, usually within 1 to 3 days of arrival.
Your calibration and settings stay in the ECM, so it goes back on plug and play. For more on the process, read Cummins ECM repair.
Keeping ISX downtime short
Ship overnight both ways, tell us the truck is down, and include the engine serial number, part number and fault codes. Fleets with several ISX trucks often keep a repaired spare ECM on the shelf so a swap takes under an hour.
What to include when you ship
A short note in the box speeds everything up. Include your name, phone number and return address, the engine serial number, the part number from the label, the symptoms and any fault codes with how often they occurred. Tell us if the truck was jump-started, welded on, washed or driven through deep water just before the problem started; that often points straight to the failed circuit.
Pack the module in a strong box with padding on every side, and cover the connectors so the pins cannot bend. Ship it with tracking, and use overnight service if the truck is down.
Frequently asked questions
How much does Cummins ISX ECM repair cost?
$399.99 on our price list, with a 1-year warranty.
How long does Cummins ISX repair of the ECM take?
Usually 1 to 3 days in our shop after it arrives, plus shipping.
Do I need to reprogram a repaired ISX ECM?
No, in most cases. Your calibration stays in place.
Where is the ECM on an ISX?
On the side of the engine block, mounted on rubber isolators.
Send us your ISX ECM
Call 726-999-0231 or contact us with your module name and part number. Official Cummins information is at cummins.com.