Description
Caterpillar ECM repair 40 pin is our mail-in repair for the older 2-plug Cat ECMs with 40-pin connectors. You send us your original unit; we test it, repair it, test it again and ship it back to you, with return shipping included and a 1-year warranty on the repair.
Because we repair your own ECM, its programming stays in place and in most trucks it goes back in plug and play. Below: which engines use the 40-pin ECM, what the repair costs, the mail-in steps and what to check before you ship.
On this page
Which engines use the 40 pin Cat ECM
The 40-pin Caterpillar ECM has two connectors with 40 pins each. You find it on these engines:
- C10, C11, C12 and C13
- 3126 medium-duty engines
- 3406 (including the 3406E) and 3176 heavy-duty engines
We repair every 2-plug 40-pin unit, whatever the part number or engine serial prefix. Part numbers we see on 40-pin units include 117-4017, 117-8351, 108-0491 and 145-7806 (older 3406E engines with the 5EK, 1WL and 6TS prefixes) and 145-7801 (C12, prefix 9NS). Several of these engines were also built with the newer 70-pin ECM, so count the pins on the connectors before you order:
| Connector on your ECM | Repair listing | Price |
|---|---|---|
| 2 plugs, 40 pins each | Caterpillar ECM repair 40 pin (this listing) | $699.99 |
| 2 plugs, 70 pins each | Caterpillar ECM repair service (70 pin) | $619.99 |
| 120-pin connector | Caterpillar ECM repair 120 pin | $699.00 |
40 pin Cat ECM repair cost
- 40 pin Cat ECM repair: $699.99, return shipping in the US included.
- Test fee: $149 if the unit can’t be repaired or we find no fault.
- Shipping to us: paid by you, with any carrier.
- Optional tune: add the Caterpillar ECM tune service for more horsepower while the unit is here.
We don’t diagnose over the phone: the unit has to be on our bench before we can say whether it can be repaired.
How the Caterpillar ECM repair 40 pin process works
- Add this repair to your cart and check out. At the end you get an invoice: print it.
- Pack the ECM with the invoice and your phone number. Our printable repair form has room for the engine serial number and notes.
- Ship it to: Repair Department, 9317 Jacksboro Hwy, Fort Worth, Texas 76135.
- We test and repair the unit, usually within 2-3 days of receiving it.
- We ship it back with tracking, return shipping included.
More on mail-in repairs for every brand: ECM repair service.
Check these before you ship your ECM
Many “dead ECM” trucks have a cheaper problem. Before you pull the unit, check:
- Batteries and grounds: low voltage or a bad ground looks like an ECM failure.
- Fuses and the ECM power supply at the connector.
- The harness and connectors: chafed wires, corrosion or water in the plugs.
- Sensors that set codes, such as speed and timing sensors.
Our guide to bad ECM symptoms walks through each check, and 8 signs your Caterpillar ECM is failing covers the Cat-specific ones.
Repair or replace a 40-pin Cat ECM?
Repair is usually the better deal when the unit is not burned, cracked or flooded and the truck can wait a few days: you keep your original programming and pay less. A remanufactured replacement makes sense when the unit is physically damaged or you need the truck running now. Browse Caterpillar ECMs or look up the number on your label in our ECM part number list.
Want to know more about what the ECM does? This overview of engine control units explains the basics, and our Cat ECM guide covers the 40-pin and 70-pin units in detail.
Warranty
- 1-year warranty on every Caterpillar ECM repair 40 pin job: see our warranty.
- Labor and downtime costs are not covered.
- The ECM should be installed by a professional technician.
Frequently asked questions
How do I know my Cat ECM is a 40-pin unit?
Look at the two large connectors on the ECM. If each one has 40 pins, this is your listing. If they have 70 pins, use the 70-pin repair; if there is a 120-pin connector, use the 120-pin repair.
Will my truck need programming after a 40 pin Cat ECM repair?
Usually not. We repair your own unit, so the programming stays in place and it goes back in plug and play in most trucks.
What happens if my ECM can’t be repaired?
We call you. We can send it back for the $149 test fee, or offer a remanufactured replacement programmed for your engine.
Can I add a horsepower tune to the repair?
Yes. Add the Caterpillar ECM tune service to the same order and we tune the unit before it ships back to you.
Get your 40-pin Cat ECM repaired by 1EngineControl
Our Caterpillar ECM repair 40 pin service is done in-house in Fort Worth, Texas, with return shipping included and a 1-year warranty. Questions? Call 726-999-0231, read the FAQ or contact us.




Reviews
Bought this? Be the first to review it.